Vax 4000 Model 200 Technical Information Seite 1

VAX 4000 Model 200Technical InformationOrder Number EK–396AB–TM–002Digital Equipment CorporationMaynard, Massachusetts

1.3 Power-UpAt power-up, the console program determines the console device type andconsole language, then runs the self-tests for the CPU and memory.

Figure 3–1: VAX 4000 Model 200 (BA430 Enclosure) ConfigurationWorksheetMLO-005711Current (Amps)+12 VdcPower(Watts)Mass Storage:CPU 1Mem 2Mem 3Mem 4Mem

Figure 3–2: VAX 4000 Model 200 (BA215 Enclosure) ConfigurationWorksheetPrimary Power SupplySlot ModuleCurrent (Amps) Power(Watts)Mass Storage:Mem 2Q/C

Table 3–1: Power RequirementsCurrent (Amps)MaxPowerMaxBusLoadsOption Module +5 V +12 V Watts AC DCAAV11–SA A1009–PA 2.10 0.00 10.50 2.5 0.5ADQ32–SA A0

Table 3–1 (Cont.): Power RequirementsCurrent (Amps)MaxPowerMaxBusLoadsOption Module +5 V +12 V Watts AC DCMS650–BB M7622–BB 3.1 0.00 15.5 – –RF31E–AA/

IndexAAsynchronous serial controllersdescription of, 2–38BBA430 enclosure, 1–1Base systemdescription of, 1–1Break Enable/Disable switchdescription of

MMass storage controllersSee ControllersModulesKA660–AA/–BA CPU, location of,1–1MS650–Bx memory, location of,1–1MS650–Bx moduleand maximum supported n

Table 1–1: Console I/O Mode Control CharactersCharacter ActionReturnalso <CR> The carriage return ends a command line. No action is taken ona co

Table 1–1 (Cont.): Console I/O Mode Control CharactersCharacter ActionCtrl/REchoes <CR><LF>, followed by the current command line. Can beu

Table 1–2: Console I/O Mode CommandsCommand ActionBOOT Initializes the processor and transfers execution to the VMB.CONFIGURE Invokes an interactive m

Table 1–2 (Cont.): Console I/O Mode CommandsCommand ActionSET RECALL Sets command recall state to either ENABLED (1) or DISABLED(0).SHOW BFLAG Display

Table 1–2 (Cont.): Console I/O Mode CommandsCommand ActionTEST Invokes a diagnostic test program specified by the test numberyou enter. If you enter a

Example 1–1 (Cont.): SHOW QBUS DisplayScan of QBUS Memory Space>>>-20000120 (760400) = 0080 (300) DHQ11/DHV11/CXA16/CXB16/CXY08-20000122 (760

Example 1–1 (Cont.): SHOW QBUS DisplayScan of Qbus Memory Space-30040000 to 3005ffff (01000000 to 01377777)>>>For each address, the console d

Example 1–4: SHOW LANGUAGE Display>>> SHOW LANGUAGEEnglish (United States/Canada)>>>Example 1–5: SET LANGUAGE Command>>> SE

Table 1–3: Boot Device NamesDevice Type Controller/Adapter Device Logical NameRF-series ISE Embedded DSSI host adapter(part of CPU)DImn1RF-series ISE

First Printing, December 1990Revised, June 1991The information in this document is subject to change without notice and should not beconstrued as a co

1.5 Digital Storage Systems Interconnect (DSSI)The KA660 CPU module contains an embedded DSSI chip on the modulewhich becomes a DSSI bus interface con

1.6 KA660–AA-BA CPU SpecificationsThe VAX 4000 Model 200 system (in a BA430 enclosure and in a BA215enclosure) uses the KA660–AA central processing uni

PerformanceInstruction prefetch buffer size 12 bytesOn-chip cacheSize 6 KbytesSpeed 28 nanosecondsAssociativity Direct mappedTranslation BufferSize 64

Console Serial LineInterface standards EIA RS–423–EIA V.10 X.26EIA RS–232–C/CCITT V.28DEC–423Data format 1 start bit, 8 data bits, 0 parity bits, 1 st

Chapter 2Option SpecificationsThis chapter lists specifications for the options currently supported in theVAX 4000 Model 200 system, grouped as follows:

2.1 Options OverviewThe option specifications include the following, where applicable:• Functional information• Ordering information• Performance• Confi

2.2 Mass Storage OptionsThe VAX 4000 Model 200 system supports the following mass storagedevices:• Internal to the BA430 and BA215 enclosures:TK-serie

2.2.1 KDA50 ControllerThe KDA50 is an intelligent controller that interfaces with up to four SDI-compatible mass storage devices on the Q22-bus.Functi

2.2.2 KFQSA Storage AdapterThe KFQSA is an intelligent storage adapter that allows Q22-bus systemsto communicate with storage peripherals based on the

2.2.3 KLESI ControllerThe KLESI–SA is a controller that interfaces with the TU81–Plus tapedrive on the Q22-bus.Functional InformationController protoc

ContentsPreface viiChapter 1 Base System Description1.1 System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–11.2 Fir

2.2.4 KZQSA Storage AdapterThe KZQSA storage adapter controls the TLZ04 and RRD-series devices onthe Q22-bus.Functional InformationAdapter protocol TM

2.2.5 RA60 Disk DriveThe RA60 disk drive is a high-capacity removable disk drive that provides205 Mbytes of formatted storage space. The VAX 4000 Mode

2.2.6 RA70E Disk DriveThe RA70E disk drive is a high-capacity fixed-disk drive that provides 280Mbytes of formatted storage space. The VAX 4000 Model 2

2.2.7 RA81 Disk DriveThe RA81 disk drive is a high-capacity fixed-disk drive that provides 456Mbytes of formatted storage space. The VAX 4000 Model 200

2.2.8 RA82 Disk DriveThe RA82 disk drive is a high-capacity fixed-disk drive that provides 623Mbytes of formatted storage space. The VAX 4000 Model 200

2.2.9 RA90 Disk DriveThe RA90 disk drive is a high-capacity fixed-disk drive that provides 1.2gigabytes of formatted storage space. The VAX 4000 Model

2.2.10 RA92 Disk DriveThe RA92 disk drive provides 1.5 Gbytes of formatted storage space. TheVAX 4000 Model 200 supports the RA92 only in separate sto

2.2.11 RF31 Integrated Storage Element (ISE)The RF31 is a DSSI integrated storage element (ISE) that provides 381Mbytes of formatted storage space. An

2.2.12 RF31F Integrated Storage ElementThe RF31F is a DSSI integrated storage element (ISE) that provides 200Mbytes of formatted storage space. The RF

Configuration InformationForm factor Standard 5.25-in footprintData surfaces 8Bits per inch 30,064Tracks per inch 1,875Power requirements +5 Vdc, 1.3 A

2.2.13 RF71 Integrated Storage Element (ISE) . . . . . . . . . . . . . . 2–172.2.14 RF72 Integrated Storage Element (ISE) . . . . . . . . . . . . . .

2.2.13 RF71 Integrated Storage Element (ISE)The RF71 is a DSSI integrated storage element (ISE) that provides 400Mbytes of formatted storage space. An

2.2.14 RF72 Integrated Storage Element (ISE)The RF72 is a DSSI integrated storage element (ISE) that provides 1.0Gbytes of formatted storage space. RF

Related DocumentationEK–RF72D–IM RF31/RF72 Installation Manualfor BA200 EnclosuresEK–RF72D–UG RF31/RF72 User GuideOption Specifications 2–19

2.2.15 RRD40 Compact-Disc SubsystemThe RRD40 is a CD reader that retrieves data in fixed-length blocks fromremovable compact-disc media.Functional Info

2.2.16 RRD42 Optical Compact-Disc SubsystemThe RRD42 is a 600-Mbyte optical CD reader that retrieves data in fixed-length blocks from removable compact

Configuration InformationForm factor Standard 5.25-in high, full rack widthRelated DocumentationEK–RRD42–OM RRD42 Disc Drive Owner’s Manual2–22 VAX 400

2.2.17 TF85 Tape DriveThe TF85 is a cartridge tape subsystem that can store up to 2.6 Gbytes.The TF85 is a streaming tape drive with a built-in DSSI (

Physical SpecificationsHeight 8.25 cm (3.25 in)Width 14.60 cm (5.70 in)Depth 21.44 cm (8.44 in)Weight 15.4 kg (7.0 lb)Configuration InformationForm fact

2.2.18 TK50 Tape DriveThe TK50 is a streaming-tape drive subsystem that can store up to 95Mbytes on a tape cartridge for backup data storage.Functiona

Physical SpecificationsHeight 8.25 cm (3.25 in)Width 14.60 cm (5.70 in)Depth 21.44 cm (8.44 in)Weight 2.27 kg (5.0 lb)Configuration InformationForm fact

2.6 Graphics Adapters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–742.6.1 VS30U Graphics Adapter . . . . . . . . . . . . . . .

2.2.19 TK70 Tape DriveThe TK70 is a streaming-tape-drive subsystem that can store up to 296Mbytes on a tape cartridge for backup data storage. The TK7

Configuration InformationForm factor Standard 5.25-in footprintPower requirements +5 Vdc, 1.35 A; +12 Vdc, 2.4 APower consumption 35.6 WBus loads 0.0 a

2.2.20 TLZ04 Tape DriveThe TLZ04 is a 1.2 Gbyte cassette (DAT) SCSI tape drive, either tabletopor embedded in the VAX 4000 Model 200 system.Functional

Physical SpecificationsHeight 10.0 cm (3.8 in), tabletop8.2 cm (3.35 in), embeddedWidth 32.5 cm (12.7 in), tabletop14.60 cm (5.70 in), embeddedDepth 28

2.2.21 TQK70 ControllerThe TQK70 controller module provides the interface between the TK70 tapedrive and the Q22-bus.Functional InformationController

2.2.22 TSZ07 Tape DriveThe TSZ07 is a high-capacity, streaming, 9-track, reel-to-reel, half-inchmagnetic tape drive with dual recording densities. The

Physical SpecificationsTabletopHeight 26.78 cm (10.50 in)Width 50.36 cm (19.75 in)Depth 68.85 cm (27.00 in)Weight 36.8 kg (81 lb)RackmountHeight 22.32

2.2.23 TSV05 Tape DriveThe TSV05 is a magnetic streaming-tape-drive that provides 40.5 Mbytesof backup data storage. The TSV05 reads or writes up to 1

2.2.24 TSV05 ControllerThe TSV05 tape drive controller interfaces the TSV05 tape drive to theQ22-bus.Functional InformationController protocol Control

2.2.25 TU81–Plus Tape DriveThe TU81–Plus is a reel-to-reel tape drive mounted in a 101.6-cm (40-in) cabinet. The drive supports two industry-standard

PrefaceThis manual provides a summary of technical information about the VAX4000 Model 200 system.• Chapter 1 describes the base system and lists spec

Physical SpecificationsHeight 105.8 cm (41.7 in)Width 54.6 cm (21.5 in)Depth 76.2 cm (30.0 in)Weight 139 kg (295 lb)Related DocumentationEK–TU81E–UG TU

2.3 Communications OptionsThe VAX 4000 Model 200 system supports the following communicationsoptions:• CXA16 asynchronous multiplexer (16 lines)• CXB1

2.3.1 CXA16 Asynchronous Multiplexer (16 lines)The CXA16 is an intelligent, preprogrammed serial controller that canoperate in either DHV11 or DHU11 m

Ordering InformationBC16E-series cable Office cable—data only, six-conductor, terminatedwith modified modular plugs• BC16E–10: 3 m (10 ft)• BC16E–25: 7.

Configuration InformationBus loads 3.0 ac; 0.5 dcModule connectors 2 female, 36-pin Amphenol connectorsRelated DocumentationEK–CAB16–UG CXA16/CXB16 Use

2.3.2 CXB16 Asynchronous Multiplexer (16 lines)The CXB16 is an intelligent, preprogrammed serial controller that canoperate in either DHV11 or DHU11 m

Ordering InformationH8572 Cable extender. Null modem cable terminatedwith modified modular jacks.PerformanceTransmit data transfers Single-character pr

Related DocumentationEK–CAB16–UG CXA16/CXB16 User’s GuideEK–CAB16–TM CXA16/CXB16 Technical Manual2–44 VAX 4000 Model 200 Technical Information

2.3.3 CXY08 Asynchronous Multiplexer (8 Lines)The CXY08 asynchronous multiplexer performs data concentration, real-time processing, and interactive te

PerformanceSingle-character or two-character programmedtransfers, or up to 16-character block mode DMAtransfers in DHU11 mode.Receive data transfers S

Chapter 1Base System DescriptionThis chapter describes the VAX 4000 Model 200 base system, including thefollowing:• Power-up self tests• Digital Stora

2.3.4 DESQA Ethernet ControllerThe DESQA Ethernet controller provides a high-speed asynchronousconnection between a Q22-bus system and a Local Area Ne

2.3.5 DEQRA Token Ring Q-bus AdapterThe DEQRA Token Ring Q-bus adapter and its software, TRDRV/VMS,enable Q-bus VAX systems to connect to 4- or 16-Mbi

Related DocumentationEK–DEQRA–IN DECTRN Controller 100 Hardware InstallationEK–DEQRA–TM DECTRN Controller 100 Hardware DescriptionAA–PH7NA–TE DECTRN D

2.3.6 DFA01 Asynchronous Controller with Integral ModemThe DFA01 is an asynchronous serial controller that emulates the DZQ11.It has two lines, each w

Configuration InformationForm factor Quad height with integral, flush cover panelPower requirements +5 Vdc, 1.97 A; +12 Vdc, 0.04 APower consumption 10.

2.3.7 DPV11 Synchronous ControllerThe DPV11 is a single-line programmable controller that provides local orremote interconnections between systems.Fun

2.3.8 DSRVB DECserver 200The DSRVB DECserver 200 is an 8-line terminal server used to connectterminals to a host computer on an Ethernet Local Area Ne

Related DocumentationAA–HL77B–TK DSRVB DECserver 200 User’s Guide2–54 VAX 4000 Model 200 Technical Information

2.3.9 DSV11 Synchronous ControllerThe DSV11 is a two-channel, high-speed, synchronous controller thatinterfaces Q22-bus backplanes.Functional Informat

2.4 Real-Time OptionsReal-time controllers interface devices that monitor processes inenvironments such as the laboratory or manufacturing. Typically,

Figure 1–1: VAX 4000 Model 200 Block DiagramDiskDSSIDisksCPUEthernetConsoleMainMemoryReal-TimeDevicesCommunicationDevicesQ-busMLO-005710TapeController

2.4.1 AAV11–S Digital-to-Analog ConverterThe AAV11–S is a digital-to-analog converter with DMA capability. TheAAV11–S is functionally equivalent to th

Configuration InformationForm factor Dual heightPower requirements +5 Vdc, 2.10 A (typ); +12 Vdc, 0.0 APower consumption 10.5 WBus loads 2.5 ac; 0.5 dc

2.4.2 ADQ32 Analog-to-Digital ConverterThe ADQ32 is an analog-to-digital converter with DMA capability.Functional InformationInput channels 32 single-

PerformanceA/D outputData buffer register 16-bit read-only output registerResolution 12 bits unipolar; 11 bits bipolar plus sign bitData notation Stra

2.4.3 ADV11–S Analog-to-Digital ConverterThe ADV11–S is an analog-to-digital converter with DMA capability. TheADV11–S is functionally equivalent to a

PerformancePower off 1 K in series with a diodeInput bias current ±20 nA at 25°C (77°F) maximumInput protection Inputs are current-limited and protect

2.4.4 AXV11 ControllerThe AXV11–S is an input/output circuit board for analog devices. TheAXV11–S is functionally equivalent to the AXV11–C.Functional

PerformanceSystem throughput 25K channel samples/secondD/A converter specificationsNo. of D/A converters 2Digital input 12 bits (Binary code is used fo

2.4.5 DIV32 ControllerThe DIV32 is a quad-height, integrated services digital network (ISDN)communications controller with connection to the Q22-bus b

2.4.6 DRQ3B Parallel InterfaceThe DRQ3B is a high-speed parallel interface that provides twoindependent 16-bit, unidirectional data channels.Functiona

1.2 Firmware OverviewTwo electrically programmable read-only memory (EPROM) chips on theKA660 CPU module contain the firmware. This firmware consists of

2.4.7 DRV1W Parallel InterfaceThe DRV1W is a general-purpose, parallel interface with one 16-bit inputport and one 16-bit output port. The DRV1W suppo

Configuration InformationModule connectors Two 40-pin connectorsRelated DocumentationEK–DRVWA–UG DRV11–WA General Purpose DMA User’s Guide2–68 VAX 4000

2.4.8 IBQ01 ControllerThe IBQ01 is a DMA controller that interfaces a Q22-bus system to RS–485industrial control and measurement devices.Functional In

2.4.9 IEQ11 ControllerThe IEQ11 option is a DMA controller that interfaces a Q22-bus system totwo independent instrument buses (IEC/IEEE).Functional I

2.4.10 KWV11–S Programmable Real-Time ClockThe KWV11–S is a programmable real-time clock that can be programmedto count from one to five crystal-contro

PerformanceHysteresis Approximately 0.5 V, positive and negativeCharacteristics Single-ended input, 100-K impedance to gndClock outputSignal CLK OV L

2.5 Printer Interface2.5.1 LPV11–SA Printer InterfaceThe LPV11 printer interface controls the flow of data between the Q22-busand a line printer.Orderi

2.6 Graphics Adapters2.6.1 VS30U Graphics AdapterThe VS30U is a full-page, high-resolution DMA color video subsystemcapable of 8-plane color video mem

Chapter 3System ExpansionThis chapter provides guidelines on how to expand your VAX 4000 Model200 system.3.1 Planning System ExpansionYou must conside

by means of switches or jumpers on the options themselves. Digital servicerepresentatives configure the options when they install them. Your Digitalser