Vax V-002 Bedienungsanleitung

5.6 Set Point Method Menu ... 5.7 Burst Image Acquisition Using 1Oms Spacing. ... 5.8 Burst Image Acquisition Mod

- 8.4 Chart Selection and Setup Menu ... 8-11 8.5 Run-Only Short SPC Setup Menu ... 8-15 8.6 Short SPC Setup M

- -

User Experience Related Publications Introduction The SLS Configuration Support Software (CSS) is a user-friendly, menu-driven software pack

l dBASE User’s Manual l Lotus l-2-3 User’s Manual Overview: Installation The DataMyte Handbook and MetriStat User’s Manual are useful if

Configuration records developed while using Version 1.0 are not compatible with Version 2.0. Thus, if you have Version 1 .O configurat

you to exit to the disk operating system (DOS). Here is a brief description of each option in the Main Menu: Configure -This option

Software Package: Items Included Hardware Requirements Installation Installing the SLS Configuration Support Software (CSS) includes two main

l Display adapter: A graphics display adapter and monitor (to support the View Image and Statistical Process Control options). The CS

- Note the two alignment keys on the 4-pin connector Refer to Appendix A, RS-232 Cable Connections, for pinout information. Carefully a

Important User Information Solid state equipment has operational characteristics ? differing from those of electromechanical equipment. “Ap

Setting the Remote Configuration Switch - The Remote Configuration switch on the SLS must be set to “Enable” so that the SLS can comm

Note the column of 12 “DIP” switches. These 12 “rocker” switches select the SLS analysis function and operating parameters, including the

Software Removal In the event that you need to remove the CSS along with al! logs and saved statistics, you can use the following

Staging the SLS and Initializing the CSS Your Action Find the bar pattern labeled “Aiming Target” in the back of this manual. Orient the ba

Figure 3.1 Aiming Target Orlentatton Relative to the SLS Inspection direction Type in “SLS,” then press This initializes the CSS. After

nart Linear Sensor Figure 32 Main Menu thin tlenu Uersion 2.88 Select an option using J and t then press ENTER. Fl for help. F2 chang

Preparing an SLS Use the following procedure to prepare an example Configuration configuration and send it to the SLS. At this point,

- Press the ENTER key to When you press the ENTER key, the Configuration Screen select the Add option. appears on the screen, as s

Figure 36 We hardwm switch settings? Sakclion - art Linear Sensor Conf igurat ion Screen Version 2.4 I Fill in the configuration screen.

- Use the space bar and Note that the Remote Configuration switch is not included ENTER key to conjigure the remaining switches as in this group

- Introduction Chapter I UserExperience ... l-l Related Publications ... l-l Overview: In

because of space limitations). The SLS Function field shows the current selected function. Ifyou see “1-D Spaliul Measurement” in the f

- Using the View Image Option Your Action Comments Press the “V” key to highlight the View Image option in the Main Menu. Press the ENTE

Figure 3.11 View Image Display of the Aiming Target piixiq I t Black bar Black-gray-black white / c \ White 1) First edge: 28.5~ 2) Last edge:

Figure 3.12 lnwted Line Image Diilay of the Aiming Tqet ET -t wbitc wllib? White - 7 I L J Black bar Black-gray-black Chapter 6, View Image, prov

Using the Monitor Option The following procedure shows you how to select and use the Monitor option. The Monitor option displays result

- Fgure 3.14 Monitoring Smart Sensor Screen Smart Linear Sensor Bonitoring Smart Sensor Version 2.86 Press Fi for help. Press ESC when d

Using the SPC Option - The following procedure shows you how to select and use the Statistical Process Control (SPC) option. The SPC o

Verify that the cursor is highlighting “‘X Bar and R and Histogram,” then press the ENTER key. Figure3.W ChmtSeMionandSeiupMenu K Bar and H

Figure 3.17 WC Data Display: X Bar and Rand Histogram Summary of CSS Procedures When using the CSS, keep in mind the following main pr

Keyboard Usage User Interface: Getting Around The “user interface” is the point at which you interact with the CSS. More specifically,

Considerations When Using the Send Option ... S-4 Configuration Screen Fields ... 55 Description ...

l F5: Function key #5 clears all data from a data entry field, regardless of the position of the data entry cursor. l F6: Function

,- Using the Keyboard This section contains a procedure that illustrates the functions of the keys listed previously. It doesn’t cover e

Your Action Press the down arrow key. Press the letter “S” key, Press the up arrow key. Press the ENTER key. Use the following proced

Figure 4.3 Fl Key: Displaying the Main Menu Help Message iDMrt Linear Sensor Help Version 2.00 Use PgUp, PgDn, Hone, End, 1, and t to

Figure 4.4 Fi Key: String !3earch Function hart Linear Sensor klP Version 2.88 - I Use PgUp, PgDn, Hone, End, 1, and t to uiw. Fl to se

Figure 4.5 Configuration Menu &art Linear Sensor Configuration tlenu Uersion 2.EU IrIm . Insert Delete Hodify Ouerwite Send Report View

- r Snart Linear Sensor Figure 4.7 SLS Function S&don Menu SLS Function Selection Ienu Version 2.80 ss TAB to moue to the nenu or SPfI

- Figure 4.9 Menu After Pressing the Down Arrow Key Twice Targeting Light On Setup / Teach Node Strobe Lighting Output Normally Closed Pre

Mouse Usage - This section contains a procedure that illustrates the functions of the mouse. Not every possible situation is covered, o

Your Action Comments Move the mouse cursor over the down arrow prompt in the prompt line. The prompt line is near the top of the sc

- Monitor Option Chapter 7 Monitor Menu: Function Selection ... 7-2 Monitor Display: Features and Symbols ... 7-3

Move the moue cursor The help message scrolls to the last page. over the Endprompt, then click the mouse button. Move the mouse curs

Specification Limits (USL and LSL) . . . . . . . . . . . . . 8-21 - Result Description: Chart A and Chart B . . . . . . . . . . 8-21 C

Text File/Lotus 123.PRN Format ... 8-55 MetriStat Lab Format ... 8-57 DataMyte ‘kboSPC.PRN Format ...

Glossary Appendix 6 SPC Formulas Appendix C Formula Variables ... C- 1 Formulas ...

3.1 Aiig Target Orientation Relative to the SLS ... 3.2 MainMenu.. ......... 3.3 Cm&ration Menu ....